818-700-9712

OFF-ROAD  RACING
Superior Performance that out performs the competition

Sway-A-Way has been involved in off-road since the late 60’s. Sway-A-Way has always focused on building the best quality products that out perform the competition. Sway-A-Way products have been installed on winning off road cars for more than 35 years. Products include axles, torsion bars, leaf springs, adjusters, shocks and sway bars for a wide variety of applications including buggies, sand cars, trucks and crawlers. Sway-A-Way products handle the terrain. There is no substitute!

Rear Torsion Adjusters & Centers - 2008 Prices
Rear Torsion Adjusters are designed for a quirk and easy way to adjust the preload on the rear torsion bars. These units can be welded into a rear torsion housing or can be ordered with your new chassis. The removable adjusting arms are manufactured from alloy steel and heat treat for maximum strength. Adjustment is as simple as turning a screw, one for each side allowing easy changes in ride height and cornering weights. These units are available in the strong standard design or the stronger King Kong racing version. Our 40-tooth torsion center is designed for replacement of that worn out stock center or can be used in new custom car construction where adjustability is not needed. Welds into place.

Spring Plates IRS Applications
Sway-A-Way spring plates are available for both the swing axle and IRS rear suspension. Both are manufactured from high quality _” thick spring steel. The spline 4130-spring plate collars are precision welded into place and are available in several different lengths to allow use of different length torsion bars.

Spring Plates are available in pairs only and are manufactured in two different grades of steel. The standard race proven spring plates come silver zinc plated for corrosion protection. For the racer, fully heat-treated and shot peened 4130-chromoly swing axle plates are manufactured.

VW IRS Spring Plate Applications - 2008 Prices

Adjustable Spring Plates - Swing Axle Applications
Adjustable Spring plates are built the same way as the standard plates, except that they are adjustable. These bolt-on spring plates allow about 1 _” of up or down adjustment by turning one screw on each on side. The kits come complete with a full set of inner and outer urethane grommets and are available for both IRS and Swing Axle applications.

VW Swing Axle Spring Plate Applications - 2008 Prices

Sway-A-Way Sway Bars
Sway bar kits improve the over all handling and stability of your vehicle.

Contract Sway Bar Manufacturing
Sway-A-Way manufactures a wide variety of sway bars for customers who want to put their own sway bar kits together. Constructed of high-grade spring steel, each bar is precisely made on a CNC Bender. Ends can be forged or machined per requirements. Sway-A-Way can design any sway bar for your specific needs. Finishes include powder coat paint, plate, and no finish. Please contact our sales department for more information. Private label Sway bar manufacturing is available in quantity orders of 25 and more.

Off Road Sway Bars - 2008 Prices
Sway-A-Way Off Road Sway bars are designed for the severe conditions of Off Road Racing. They are manufactured in two different spine ends depending on the diameters needed and in custom lengths. Made from heat treated alloy steel, these sway bars will handle large angles of deflection with out setting, giving the driver more control. Sway bar arms are made from 2024 T-6 aluminum and available for both end diameters. The 28” arms can be cut off to shorter lengths as needed. Get more control over you race car.

Racing VW Torsion Bars - 2008 Prices

VW Rear Torsion Bars - 2008 Prices

VW/Porsche Wheel Studs and Nuts - 2008 Prices
Sway-A-Way's VW Wheel studs and nuts are manufactured from top quality aircraft alloy steel. Both the nuts and studs are cold headed, and all threads are rolled for maximum strength. Two of the studs, Part No. 8030 & 8040 have NASCAR type starting threads for perfect nut alignment and fast tire changes. Installation requires a hole drilled and reamed to .562” diameter. Sold Individually. All threads are stock 14mm-1.5 pitch.

VW Hardened Transmission Keys - 2008 Prices
VW Transmission keys for 3rd and 4th gear, are hardened to help prevent shearing. Stock keys tend to shear under high loads causing loss of both gears. These keys fit 1961-1967 bug pinion shafts and most racing ring and pinion sets including bus.

VW Rod End Adapters - 2008 Prices
The Rod End Adapter is made to replace standard ball joints with high quality heim joints for more precise steering.